- #Cisco 2950 switch configuration using console how to#
- #Cisco 2950 switch configuration using console serial#
- #Cisco 2950 switch configuration using console full#
- #Cisco 2950 switch configuration using console password#
- #Cisco 2950 switch configuration using console series#
Our simplified procedure would focus only on the basic commands of this procedure and not the full details. Don’t worry we will create a simplified similar procedure in our next topic. It may seem complicated to look at the procedure.
#Cisco 2950 switch configuration using console series#
Together we have 12 simplified summary of procedure to configure a 2950 Catalyst series switch. Local updater ID is 10.10.10.1 on interface Vl1 (lowest numbered VLAN interface found) To if our configuration has been put into place. And our seemingly last procedure is to check the VTP status. Eleventh to verify our configuration we might need to check it by using the Show VLAN command and the Show VTP status command such as follows.ġ2. Switch1(config)#interface fastethernet0/18ġ1. In this procedure we will assign fastethernet0/18 as our trunk link. Tenth we also need to create a trunk link that will serve as a link to other device in the network.
#Cisco 2950 switch configuration using console password#
Setting device VLAN database password to rulesġ0. Ninth add a VTP password of rules to the switch such as. Eight change the vtp domain to the name of your choice.Ĭhanging VTP domain name from NULL to Jeremyĩ. By default a Catalyst switch is a VTP server.Ĩ. Seventh we need to configure our switch as a VTP server or a client if there is another switch. VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2ħ. Sixth to verify our VLAN configurations we need to see it by using the Show VLAN command.ġ default active Fa0/1, Fa0/10, Fa0/11, Fa0/12ġ0 VLAN0010 active Fa0/2, Fa0/3, Fa0/4, Fa0/5ġ6 VLAN0016 active Fa0/6, Fa0/7, Fa0/8, Fa0/9 Switch1(config-if-range)#switchport access vlan 16Ħ. Switch1(config)#interface range fastethernet0/6-9 Fifth assign ports to VLAN 16 starting from ports fastethernet0/6 to fastethernet0/9. Switch1(config-if-range)#switchport access vlan 10ĥ. Switch1(config)#interface range fastethernet0/2-5 Fourth we need to assign ports starting from port fastethernet0/2 to fastethernet0/5 to VLAN 10. Please consult userĭocumentation for configuring VTP/VLAN in config mode.Ĥ. % Warning: It is recommended to configure VLAN from config mode,Īs VLAN database mode is being deprecated. Third we need to add VLAN 10 and VLAN 16 to the switch. %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to upģ.
%LINK-5-CHANGED: Interface Vlan1, changed state to up After giving the switch a host name we proceed with assigning an IP address to the VLAN1 of the switch. %SYS-5-CONFIG_I: Configured from console by consoleĢ. First we need to assign a host name to the switch.Įnter configuration commands, one per line.
#Cisco 2950 switch configuration using console how to#
when next time start the switch, there is no password required.Our topic for today will focus on how to configure the VLAN on a Catalyst 2950 Series Switch.ġ.
In command line, type "flash_init" after"switch:_", and it will initialize the flash system.The system has been interrupted prior to initializing the flash file system,and it wills show the following information.In Windows XP,click "Start" menu,and then move to "Accessories"->"Communications"->"Hyper Terminal".Plug the power cable at back of the Switch, and Holding "mode" button at left corner of the front panel for 15 seconds.
#Cisco 2950 switch configuration using console serial#